P1306 Engine Trouble Code

When you check engine light came on code P1306 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P1306 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes P1306 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

P1306 Code Meaning :

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P1306 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P1306 OBD-II Trouble Code Kickdown Relay Pull In Circuit Fault is one of the definitions for the P1306; however your vehicles manufacturer may have a different definition for the P1306 code. Please check below for your specifi P1306 code. Fuel Rail Pressure Sensor Circuit Malfunction and Cylinder 10 Contribution/balance Fault causes most of code P1306.

Reason For P1306 Code

The reason of P1306 OBD-II Engine Trouble Code is Fuel Rail Pressure Sensor Circuit Malfunction.

P1306 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is over-retarded, the engine trouble light will be illluminated and the code will be set.

How To Repair P1306 Code

Before starting let's see P1306 repairing process steps:

• Qualified technicians will begin by using a scan tool to access P1306 code stored in the ECU.
• Technicians will note P1306 code present and any freeze frame data associated with them.
• After all, if you sure the engine trouble is finished, the code will be cleared.

B for the vehicle's clutch is giving the wrong voltage readings, there could be an issue with the solenoid, the sensor, the wiring, or with the clutch itself. Shifting may become harsh, and other transmission problems may occur.

This process helps the mechanic narrow down the exact cause of the issue. If the transmission fluid fix did not cause the code to disappear from the PCM, then next step is to inspect the electrical components, and to continue working through possible repairs until the correct issue is found.

Sometimes P1306 code comes with P130600 code.

Diagnosis Of Engine Error OBD Code P1306

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P1306 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P1306 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.